====== EOS ======
===== show =====

==== save show ====

<code>
shift + update
</code>

===== patch =====

==== patch by address ====

<code>
format
</code>

==== remove address ====

<code>
chan 1 address enter
</code>

==== delete channel ====

<code>
delete chan 1 enter
</code>

==== chan check ====

<code>
chan 1 at 70 [softkey chan check] enter
next/previous (page up/down)
</code>

===== undo =====

==== undo last command ====

<code>
undo enter
</code>

==== undo multiple commands ====

<code>
undo page up enter
</code>

===== live =====

==== groups ====

=== add channel at the end of the group ===

<code>
group 2 enter +79 enter
</code>

=== remove chan from group ===

<code>
group 2 enter -79 enter
</code>

=== add chan in specific place in group ===

<code>
group 2 enter 79 insert before 7 enter
</code>

==== levels ====

=== add 5% ===

<code>
chan 1 at +05 enter
</code>

=== divide level by 50% ===

<code>
chan 1 at /50 enter
</code>

=== multiply level by 2 (200%) ===

<code>
chan 1 at /200 enter
</code>

=== fan level ===

<code>
chan 1 thru 10 at 1 thru full enter
</code>

==== selection ====

=== selection offset ===

<code>
chan 1 thru 10 offset 2 enter
</code>

=== select active ===

<code>
select active (ctrl a)
</code>

=== select last ===

<code>
select last (ctrl l)
</code>

==== park ====

=== park channel ===

<code>
chan 5 @ 50 park enter
</code>

=== park at current value ===

<code>
chan 5 park enter
</code>

=== park parameter ===

<code>
chan 5 color park enter
</code>

=== park address ===

<code>
address 5 @ 75 park enter
</code>

=== remove park ===

<code>
chan 5 park enter
</code>

=== unpark all ===

<code>
park enter
</code>

=== unpark address ===

<code>
address park enter
</code>

=== using park tab ===

== park channel ==

<code>
chan 2 @ 50 enter
</code>

== park address ==

<code>
address 5 @ 75 enter
</code>

== unpark channel ==

<code>
chan 2 @ enter
</code>

== unpark address ==

<code>
address 5 @ enter
</code>

==== copy to / recall from ====

=== copy channel ===

<code>
chan 1 copyto chan 2 enter
</code>

=== copy parameter ===

<code>
chan 1 color copyto chan 2 enter
</code>

===== timing =====

==== delay by parameter ====

<code>
group 1 tilt delay 5 enter
</code>

==== remove time or delay ====

<code>
group 1 delay enter
</code>

===== palettes =====

==== distribute to palettes ====

<code>
group 1 focuspalette 1 to 5 enter
</code>

==== fan with palettes ====

<code>
group 1 focuspalette 1 + 5 enter
</code>

==== record only parameter ====

<code>
group 1 goboselect record beampalette 2 enter
</code>

===== display values (need confirmation) =====

==== show values instead of palette name ====

<code>
about label
</code>

==== same but always ====

<code>
about label label
</code>

==== go back to name ====

<code>
about
</code>

===== groups =====

==== sub groups (shift+slash) ====

<code>
(chan 1+chan2)(chan 11+chan12)
</code>

===== sneak =====

==== change value with default time ====

<code>
sneak enter
</code>

==== force time ====

<code>
sneak 0 enter
</code>

==== change value for a channel with time ====

<code>
chan 1 thru 5 at 50 sneak 5 enter
</code>

===== faders =====

==== unload fader ====

<code>
shift + load 
</code>

===== cue list =====
==== release cuelist ====
<code>
goto cue 2/ out
</code>

==== go to cue 0 and home device params ====

<code>
goto cue out enter
</code>

==== go to cue 0 without touching non intensity parameters ====

<code>
goto cue 0 enter
</code>

==== reload cue 1 ====

<code>
goto cue 1 enter
</code>

==== reload active cue ====

<code>
goto cue enter
</code>

==== record next ====

<code>
record next
</code>

==== other ====

<code>
goto cue next/last
</code>

==== record blackout (et penser à mettre un block et assert sur le cue en question) ====

<code>
select active out record next
</code>

==== go to cue 5 with cue time ====

<code>
goto cue 5 time enter
</code>

==== go to cue 5 with custom time ====

<code>
goto cue 5 time 3 enter
</code>

==== preload (jump to) cue 5 to next ====

<code>
cue 5 load
</code>

==== save value only to specific cue in blind mode ====

<code>
chan 1 at 50 cue only enter
</code>

===== effects =====
usefull macro : "effect 1 Learn Time Sample BPM"
==== stop effect ====

<code>
group 1 stopeffect (ctrl+shift+e) enter
</code>

==== stop running effect ====

<code>
group 1 effect enter
</code>

==== flyout ====
[[https://www.youtube.com/watch?v=vGZ26l1CvcU|source]]
absolute effect
^action ^param ^step time ^time ^dwell ^level^
|1|intens|0|0|3.99|100.0|
|2|tilt|(0)|0|0|bkgrd|
|3|tilt|2.99|3.49|0.5|(+)-100|
|4|intens|0.75|0.5|1.5|0.0|
|5|tilt|1.5|0|0|bkgrd|

==== sym circle ====
=== version 1 ===
inspiration : https://community.etcconnect.com/control_consoles/eos-family-consoles/macros/i/macro-favorites/symmetrical-circle-effect
  * group 1 : 1 thru 4
  * group 2 : 5 thru 8
  * effect 1 : circle (standard)
  * effect 2 : circle (attributes reverse / green arrow left down (mirror hor + mirror vert)
  * macro 1 :
<sxh>
group 1 effect 1
group 2 offset reverse effect 2
</sxh>
=== version bg ===
using same effects, need to set "Axis -10" to be very symetrical
<sxh>
Offset Num_Groups 2
Next Effect 4
Next Offset Reverse Effect 5
</sxh>

=== version mega <del>bg</del> shlag ===
only working for 4 fixtures..... it is better to use version bg...
source : https://youtu.be/JagsTbVKXPI?si=Ra53JlNqQgec5tjK

<sxh>
hardkey : tab 12
chan 1 t 4 type ayrton eurus s basic
-> panel augmented3d
chan 1 thru 4 position */*/5
chan 1 thtu 4 position */4/
chan 1 thru 4 position -4/*/thru 4/*/
hardkey esc
chan 1 thru 4 record group 1
group 1 @ full
mouse : in augment3d tab, left click and maintain on the lead singer position until the machines are in place
record focus palette 1
effect effect
901 copy to 901.1
effect 901.1 reverse steps
hardkey : esc
g 1 a f f
group 1 offset chan per group 2
next
group 1 offset chan per group 2: chan 1 thru 2 effect 901
next
group 1 offset chan per group 2: chan 3 thru 4 effect 901.1
effect 901.1 axis -15
record preset 10 plus fx
ctrl+g+o+i+0
g 1 alt+p 10
</sxh>
===== a revoir =====

  * <del>block</del>
  * autoblock
  * <del>assert</del>

===== missing =====
  * group 1 at full thru 0 thru full
  * <del>group 1 beam palette 20 time 5</del> --> group 1 beam palette 20 sneak 5
  * <del>cue 2/ out</del> --> goto cue 2/ out
  * <del>where is the "move" button ?</del> --> copyto*2
  * small faders on big screen
  * locked on "syntax error"
  * out out = out time 0

===== OSC =====
==== Tests ====
<sxh python>
client.send_message("/eos/cmd", "Tilt @ +0.1#")
</sxh>
==== Show Control ====
<sxh python>
pip install python-osc
from pythonosc import udp_client
client = udp_client.SimpleUDPClient("10.0.0.1",8000)
client.send_message("/eos/cmd", "Event 1 / Network_Inputs#")
client.send_message("/eos/cmd", "Event 1 _sACN 1 / 1#")
client.send_message("/eos/cmd", "Event 1 Show_Control_Action Level_By_Address 1 / 1#")
</sxh>
<sxh python>
from pythonosc import udp_client

input_universe = 1
output_universe = 2
event_list = "2"
desk_ip = "192.168.0.100"
client = udp_client.SimpleUDPClient(desk_ip,8000)
client.send_message("/eos/cmd", "Delete Event " + event_list+ " /#")
client.send_message("/eos/cmd", "Event " + event_list+ " /#")
client.send_message("/eos/cmd", "Event " + event_list+ " / Network_Inputs#")
client.send_message("/eos/cmd", "Event " + event_list+ " / External Enable#")
for id in range(1,513):
    input_address = str(((input_universe - 1) * 512) + id)
    output_address = str(((output_universe - 1) * 512) + id)
    client.send_message("/eos/cmd", "Event " + event_list+ " / " + input_address+ " _sACN "+ input_address+ "#")
    client.send_message("/eos/cmd", "Event " + event_list+ " / " + input_address+ " Show_Control_Action Level_By_Address "+ output_address +"#")
</sxh>
==== Faders ====
To use faders, we need to define a "virtual" fader page for osc containing a fixed number of faders and then use them to control real faders.
source : https://community.troikatronix.com/topic/5351/tutorial-how-to-do-fader-communication-with-etc-eos-lighting-desk-using-osc
<sxh>
/eos/fader/1/config/10
/eos/user/2/fader/1/1 = 0.5
</sxh>